Relay 4 Channels 10 Amps
RLY-4ch-10A
RLY-4ch-10A controller, it used to control the lighting channels or shutter motors (Max 10 Amps per channel) , it can be Programmed manually for lighting channels, or by PC for advanced scene setting . also it has access holes for its mechanical relay to switch on each channel by hand in case of emergency network failure.
Important Features
– Fast and low noise relay switch each 10 Amps.
– Can be used to control 4 lighting channels or 2 different shutters or motors.
– Can Be programmed manually with TIS panels.
– Low consumption Products (15mA/24VDC Normal Running)
– Include 4 built in scenes and sequences,
– LED for network life and for each channel indicator .
– Working with TIS bus protocol
– ABS anti-flame case.
– UL USA certified relay, terminal, ICs and PCB.
– Product CE certified.
Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and other hazards.
These instructions are an integral part of the product, and must remain with the end customer.
Basic information
This device is a product of the TIS system. It is a DIN-rail mountable device with 4 independent free voltage Relay channels which can be controlled separately with TIS protocol messages, technical knowledge obtained in TIS training courses is a prerequisite to proper understanding how to install device. Basic Manual Programming can be done without the software. Advanced Programming knowledge about software obtained in the advanced training courses.
Intended use
Control lighting, curtains, light on/off, shades open/close, Motor, Pumps.
Product characteristics
|
Outputs |
Number of channels Nominal voltage Nominal current per channel Maximum total channels load
|
4 0 – 230 V AC 50/60 Hz 10 A / 230 VAC 120 A / 230 VAC |
|
Output switching current |
Max switching current
Max Continues current Max. switching Voltage
|
16A/230 VAC Resistive 8A/230 VAC florescent 10A/230 VAC 440VAC / 125VDC |
|
Output service life |
Mechanical service life
|
> 10,000,000 Times
|
|
Output switching times |
Operating time Releasing time Max. operating frequency
|
15mS (at nomi. Volt) 8 mS (at nomi. Volt) 20 cycle/min
|
|
TIS Bus |
Number of devices on 1 line Bus voltage Current consumption (Normal) Current consumption (Peak) Protection
|
Max. 64 12-32 V DC <15 mA / 24 V DC <75 mA / 24 V DC Reverse Polarity Protection |
|
Reaction time |
|
approx. 20ms |
|
Operating and display elements |
Programming button/LED 1-4 buttons By TIS bus Programming Upgrading
|
For assignment of the physical address Manually ON/OFF and Programming TIS Protocol massages and commands Manual basic Prog, or by software. 1 X mini USB for up to date upgrading. |
|
Mounting |
Din Rail Wall mount
|
Standard 35 mm Din rail screw holder on the back of the module |
|
Connection terminal |
Load and Power Data / bus
|
Screw terminal 0,25…4mm2 Male female connectors Link + screw Terminal |
|
Functions |
Lighting control ON/OFF Dimming Curtain control
|
4 channel controlled separately Can set 2 group of curtain (open/close) option
|
|
Weight |
Without packaging
|
0.21 KG |
|
Dimensions |
Width x length x height
|
90mm x 73mm x 76mm |
|
Housing |
Materials Casing color Button color IP rating |
ABS anti fire Black Gray Silver IP 20 |
|
Temperature range |
Operation Storage Transport
|
0…60°C -20…50°C -25…75°C |
|
Air humidity |
|
<85% non-condensing |
Wiring diagram
Data connection
TIS Bus connection can be done by 2 ways
Train Connector
By attaching 2 modules or more with each other on the Din rail
Screw terminals connection
By using the Cat5e cable to connect to TIS bus 4 terminals (24V,D+, D-, GND)
|
Recomanded UTP cat5e color connection |
24V – Orange D+ – Blue D- – White Blue GND – White Orange |
|
Input Phase: |
1.5 or 2.5 mm electrical wire. |
|
Load connection (1,2,3,4) : |
1.5 or 2.5 mm electrical wire. |
Warranty
We provide a warranty as provided for by law.
Hologram warranty seal and product serial number is provided by each device.
Please send the description of the defect with Product S/N to our dealer network.