TIS Dimmer 4 channels 3 Amp
DIM-4ch-3A
DIM-4ch-3A is a leading edge Dimmer.
It consist of 4 independent Channels which can control 3A lighting Load. It can be Programmed manually for lighting channels, or by PC for advanced scene .
Important Features
– 4 dimming channels each of 3A Max load.
– Data terminal surge Protection.
– over load protection.
– over heat protection.
– Over current protection
– Include 4 built in scenes and sequences,
– LED for network life and for each channel indicator .
– Working with TIS bus protocol
– ABS anti-flame case.
– UL USA certified terminal, ICs and PCB.
– Product CE certified.
TIS Leading Edge Dimmer
4 Channels 3 Amps
Model: DIM-4CH-3A
Data Sheet Rev 1.3
Safety instructions
Electrical equipment may only be installed and fitted by electrically skilled persons.
Failure to observe the instructions may cause damage to the device and other hazards.
These instructions are an integral part of the product, and must remain with the end customer.
Basic information
This device is a product of the TIS system. It is a DIN-rail mountable device with 4 independent dimmer channels which can be controlled separately with TIS protocol messages, technical knowledge obtained in TIS training courses is a prerequisite to proper understanding how to install device. Basic Manual Programming can be done without the software. Advanced Programming knowledge about software obtained in the advanced training courses.
Intended use
Control lighting, e.g. light on/off, dimming, brightness values, scene, and sequence.
It can be used for all dimmable lamps and transformers.
Product characteristics
|
Outputs |
Number of channels Nominal voltage Nominal current per channel Maximum total channels load
|
4 80 – 230 V AC 50/60 Hz 3 A 10 A |
|
TIS Bus |
Number of devices on 1 line Bus voltage Current consumption Protection
|
Max. 64 12-32 V DC <30 mA / 24 V DC Reverse Polarity Protection |
|
Protection |
Over current Over heat Over load Heat sink
|
4* internal Fuse aR class 6A Internal temp sensor protection Dimmer coil max load up to 6A Aluminum alloy with straight fin |
|
Reaction time |
|
approx. 20ms |
|
Mounting |
Din Rail Wall mount
|
Standard 35 mm Din rail screw holder on the back of the module |
|
Connection terminal |
Load and Power Data / bus
|
Screw terminal 0,25…4mm2 Male female connectors Link + screw Terminal |
|
Operating and display elements |
Programming button/LED 1-4 buttons By TIS bus Programming Upgrading
|
For assignment of the physical address Manually ON/OFF and Programming TIS Protocol massages and commands Manual basic Prog, or by software. 1 X mini USB for up to date upgrading. |
|
Functions |
Lighting control ON/OFF Dimming Scenes Sequences
|
4 channel controlled separately 4 different scenarios 4 different sequences |
|
Weight |
Without packaging
|
0.5 KG |
|
Dimensions |
Width x length x height
|
91mm x 145mm x 75mm |
|
Housing |
Materials Casing color Button color IP rating |
ABS anti fire Black Gray Silver IP 20 |
|
Temperature range |
Operation Storage Transport
|
-10…45°C -20…50°C -25…75°C |
|
Air humidity |
|
<85% non-condensing |
Wiring diagram
Data connection
TIS Bus connection can be done by 2 ways
|
By attaching 2 modules or more with each other on the Din rail |
A-Screw terminals connection
By using the Cat5e cable to connect to TIS bus 4 terminals (24V,D+, D-, GND)
|
Recomanded UTP cat5e color connection |
24V – Orange D+ – Blue D- – White Blue GND – White Orange |
Electrical wire Connections:
|
Nutral /Phase connection (N/L): |
2.5 – 4 mm electrical wire |
|
Load connection (1,2,3,4) : |
1.5 or 2.5 mm electrical wire. |
|
Earth connection: |
2.5 or 4 mm electrical wire. |
Warranty
We provide a warranty as provided for by law.
Hologram warranty seal and product serial number is provided by each device.
Please send the description of the defect with Product S/N to our dealer network.